Multistage Unlimited Frac Isolation on Coiled Tubing
NCS Multistage developed Multistage Unlimited technology as a more efficient and more economical alternative to plug-and-perf and ball-sleeve frac systems, both of which bullhead fluids down the casing, with no feedback about formation response at the frac zone, no recourse in the event of a screenout, and no way to manage water and chemical consumption. Both methods do, however, have a big appetite for pumping horsepower.
The coiled tubing solution
In developing Multistage Unlimited technology, NCS faced two challenges:
- overcome the limitations of one-way fluid movement
- find a more efficient way to isolate each stage during completion
NCS overcame both challenges by adopting coiled tubing to operate the Multistage Unlimited frac-isolation system and to open the company’s GripShift casing sleeves.
The coiled tubing work string provides a circulation path to the frac zone and also allows the use of a unique multi-set bridge plug that isolates each stage for stimulation. Current coiled tubing capabilities are more than adequate to handle multistage completion operations. Already, more than 15,000 miles of coiled tubing runs have been executed to complete more than 168,000 stages.
Circulation vs one-way fluids
With the ability to circulate or reverse circulate during completions, Multistage Unlimited systems offer more operating control:
- Acid and other leading-edge fluids can be circulated down to the isolated zone before frac pressure is applied, with returns back up the coiled tubing
- Screenouts are less likely and can be quickly removed, allowing more aggressive sand loading.
- The coiled tubing is open during fracs, to monitor formation response at the target zone in real time, allowing sand placement to be optimized.
- Sand-jet perforating can be used to access the formation, to add stages in blank casing when running the Multistage Unlimited casing sleeve system
Coiled-tubing-operated, multi-set bridge plug
The Multistage Unlimited multi-set bridge eliminates the need for composite frac plugs, which have to be run and set at every stage and drilled out before the well is put into production, and ball-seat casing sleeves that cause real problems when they don’t shift and also restrict the wellbore. With the Multistage Unlimited multi-set bridge plug, there is nothing to run in the well between fracs, nothing left in the well and nothing to drill out; just a full-open, production-ready wellbore.
The Multistage multi-bridge plug is engineered to operate reliably in a sandy environment. Pulling it up through clean fluid a short distance completely flushes any sand or proppant from the tool, leaving it ready to set at the next stage. A simple j-slot mechanism operates the plug with straight up-and-down coiled tubing movement.
The engineered-elastomer seal contains differential pressure up to 8,500 psi, well above typical formation breakdown pressure and temperatures up to 350° F. The multi-set bridge plug has been used for as many as 168 shift/frac cycles without coming out of the hole.
Casing sleeves or sand-jet perforating
To gain access to the formation for the frac, Multistage Unlimited systems use either GripShift casing sleeves or Mongoose sand-jet perforating. The sand-jet perforating sub can be run as part of any Multistage Unlimited frac-isolation assembly. For completions with casing sleeves, the sand-jet sub can be used to add stages in blank casing, without tripping out of the hole. For completions without casing sleeves, sand-jet perforating is used for all stages.
GripShift casing sleeves are shifted by setting the multi-set bridge plug in the inner sleeve, then applying annulus pressure above the seal. The inner sleeve shifts downward, opening frac ports at the top of the outer sleeve, and the frac is pumped down the coiled tubing annulus.
For sand-jet perforating, the multi-set bridge plug is set to isolate the target zone. Then an abrasive slurry is pumped down the coiled tubing and through the sand-jet sub to cut perforations through the casing and cement and into the formation. After perforating, which takes about 40 minutes, the frac is pumped down the coiled tubing annulus.
The Half-Straddle for low-rate fracs
In formations with thin reservoirs and water-bearing zones nearby, it is usually best to complete with a large number of stages and smaller fracs to avoid the water. These smaller fracs—typically 10 bpm or less—can be pumped through the coiled tubing, making it easy to control frac height. It’s called the Half-Straddle casing-sleeve option, because it resembles a coiled-tubing straddle with only a lower seal (the multi-set bridge plug), while the upper seal is achieved by closing the annulus at the surface during the frac. In general, the Half-Straddle option is a highly efficient technique that reduces water use by as much as 50% and eliminates the need for high-pressure frac stack, because the coiled tubing contains all the frac forces.